Heat Treat Foil (Tool Wrap) 309 - up to 2240F - Full rolls
By A Mystery Man Writer
Last updated 31 May 2024
Knife Making Supplies - Best prices, selection and service. Visit us Today!1
Stainless Heat Treating Foil type 309 Stainless commonly called Tool Wrap .002 thick most rolls are 20 wide Use 309 for heat treating temps up to 2240F degrees All-Foils quality Stainless Steel Use this higher temperature rated 309 tool wrap for steels that require more than 1900F for heat treat. If you are heat treating to a temperature less than 1900F the 309 wrap will still work fine, but the 321 (lower temp) is a bit cheaper. Tips: Wrap your knife one or two (at most) at a time making an airtight envelope. Fold over the seam twice and tap the seam closed with a hammer. The seam is to the side, not on 'top' of the blade - this matters later. I try to wear leather gloves any time I handle this stuff. The edges on this are razor sharp. You will believe me when you cut yourself. It's just a matter of time. Handle it with respect. Some guys put a piece of paper inside the envelope to burn up the oxygen so the blade steel does not carborize. I don't see much advantage to this. Just wrap it tight and there won't be any oxygen to speak of. Ideally, the envelope will tighten around the blade making solid contact. If you plate quench, simply leave it in the envelope and quench it inside the tool wrap. If you oil quench, you need to wrap it a little looser so you can snip the foil pouch open and dunk the blade quickly. Plate Quenching: Get scrap aluminum plates at least 1 thick. Make it a couple inches longer and at least 4 wider than your knives. When it comes time to quench, move quickly and put the (scary, hotter than hell!) foil pouch with blade blank in between the plates and press. Some guys use a wood vise with plates installed. I just press with my hand. Once between the plates, I shoot compressed air in the gap to help cool it down even quicker. For compressed air, I charge up a portable air tank from my compressor and use that up. Those little red air tanks are sold every where. Wear safety gear. I wear heavy welding gloves on both hands. I use a long tong to grab the foil pouch. I make sure the oven is OFF (getting shocked at 240v will kill you!) when pulling out the (scary, hotter than hell!) foil pouch. Holding a 1950F degree burning hot foil pouch with a blade in it is no time to figure out you are not ready. Practice a few times first before your first run. Note: Picture is for illustration only.
Stainless Heat Treating Foil type 309 Stainless commonly called Tool Wrap .002 thick most rolls are 20 wide Use 309 for heat treating temps up to 2240F degrees All-Foils quality Stainless Steel Use this higher temperature rated 309 tool wrap for steels that require more than 1900F for heat treat. If you are heat treating to a temperature less than 1900F the 309 wrap will still work fine, but the 321 (lower temp) is a bit cheaper. Tips: Wrap your knife one or two (at most) at a time making an airtight envelope. Fold over the seam twice and tap the seam closed with a hammer. The seam is to the side, not on 'top' of the blade - this matters later. I try to wear leather gloves any time I handle this stuff. The edges on this are razor sharp. You will believe me when you cut yourself. It's just a matter of time. Handle it with respect. Some guys put a piece of paper inside the envelope to burn up the oxygen so the blade steel does not carborize. I don't see much advantage to this. Just wrap it tight and there won't be any oxygen to speak of. Ideally, the envelope will tighten around the blade making solid contact. If you plate quench, simply leave it in the envelope and quench it inside the tool wrap. If you oil quench, you need to wrap it a little looser so you can snip the foil pouch open and dunk the blade quickly. Plate Quenching: Get scrap aluminum plates at least 1 thick. Make it a couple inches longer and at least 4 wider than your knives. When it comes time to quench, move quickly and put the (scary, hotter than hell!) foil pouch with blade blank in between the plates and press. Some guys use a wood vise with plates installed. I just press with my hand. Once between the plates, I shoot compressed air in the gap to help cool it down even quicker. For compressed air, I charge up a portable air tank from my compressor and use that up. Those little red air tanks are sold every where. Wear safety gear. I wear heavy welding gloves on both hands. I use a long tong to grab the foil pouch. I make sure the oven is OFF (getting shocked at 240v will kill you!) when pulling out the (scary, hotter than hell!) foil pouch. Holding a 1950F degree burning hot foil pouch with a blade in it is no time to figure out you are not ready. Practice a few times first before your first run. Note: Picture is for illustration only.
Product Details, Cut-to-fit wraps eliminate decarburization buildup, help protect from scale and oxide buildup during heat treating in atmospheric
Knights Precision Tool Wrap 100' Type 309 Stainless Steel Tool Wrap 100' x 20 x .002 Foil Wrap
China 309 Heat Treat Foil Manufacturers, Suppliers - Factory
SHOP CATEGORIES
All tool wrap is labeled 20 inch for listing purposes. The tool wrap comes from the mill 19.5 inch (+/- 0.5 inch) wide. The thickness is 0.002 and
309 Stainless Steel Tool Wrap | Heat Treat Foil 20 x .002 x 10
China 309 Heat Treat Foil Manufacturers, Suppliers - Factory
Heat Treat Ovens and Accessories - SHOP CATEGORIES
Knights Precision Tool Wrap 100' Type 309 Stainless Steel Tool
Search results for: 'knife making tools personalizer plus
Knights Precision Tool Wrap 100' Type 309 Stainless Steel Tool
Stainless Steel Tool Wrap - MSC Industrial Supply
Product Details, Cut-to-fit wraps eliminate decarburization buildup, help protect from scale and oxide buildup during heat treating in atmospheric
Knights Precision Tool Wrap 50' Type 309 Stainless Steel Tool Wrap 50' x 24 x .002 Foil Wrap
MSC Industrial Supply
Recommended for you
-
Graphite Foil By The Foot31 May 2024
-
Silver ALUMINUM Premium Roll - 12 x 200 (1 Count) - Easy Tear Aluminum Foil - Perfect For Multipurpose Kitchen & BBQ Use31 May 2024
-
EcoQuality Non-Stick Aluminum Cookie Sheet31 May 2024
-
Laboratory Grade Aluminum and Stainless Steel Foil31 May 2024
-
aluminium composite films31 May 2024
-
48 x 250' Ultra NT SCIF Radiant Barrier Foil Solid (1000 Sq. ft.)31 May 2024
-
This Genius Method For Fixing An Uneven Aluminum Foil Roll31 May 2024
-
Heavy-Duty Aluminum Foil Roll (24) - WebstaurantStore31 May 2024
-
Katbite Aluminum Foil Heavy Duty 12inx150ft, 25 Micron Thick Strong Foils Aluminum Roll with Serrated Cutter for Home Cooking, Catering, Grilling31 May 2024
-
Aluminium Foil Roll at Rs 294/roll, Aluminium Foil Jumbo Rolls in Pithampur31 May 2024
You may also like
-
Hook & Loop Tactical Strap Keychain - topthreads31 May 2024
-
😲 New things! Dark in Love, Punk Rave & Gothic Gifts 🙀 - Kate's Clothing31 May 2024
-
Actividades creativas para niños pequeños con marcadores – Zebra México31 May 2024
-
Liquipak Heavy Duty Degreaser31 May 2024
-
ฺblack And White Scissors Illustration For Making Crafts In A31 May 2024
-
Micro Stitch Starter Kit - Avery Fasteners31 May 2024
-
Hydro Flask 40 oz All Around Travel Tumbler (Birch)31 May 2024
-
Jaxx 7 ft Giant Bean Bag Sofa Dark Denim31 May 2024
-
Invisible Thread packet31 May 2024
-
Ceramic Tile Repair Ab Adhesive Set Metal Ceramic Tile - Temu31 May 2024