CerMark LMM 6000 Black for Metal – 1,000 Grams Concentrated Liquid – CerMark Sales
By A Mystery Man Writer
Last updated 15 May 2024
The CerMark LMM 6000 coating creates permanent black laser marks on hard metal types such as Stainless Steel. CerMark LMM 6000 will work with CO2 lasers with 30 or more watts of power and fiber lasers that can reach a frequency of 200 kHz. or higher. LMM 6000 will work on some aluminum grades but much slower marking s
The CerMark LMM 6000 coating creates permanent black laser marks on hard metal types such as Stainless Steel. CerMark LMM 6000 will work with CO2 lasers with 30 or more watts of power and fiber lasers that can reach a frequency of 200 kHz. or higher. LMM 6000 will work on some aluminum grades but much slower marking speed is required. LMM 6000 is NOT recommended for Chrome or softer metals like Brass, Copper and Pewter. CerMark LMM 14 is recommended for chrome and softer metals. For best results apply with an air brush. A foam brush should be used if not spraying. LMM-6000 is formulated thick to prevent settling. It may be necessary to thin the paste before using. We recommend thinning with ethanol, denatured alcohol, acetone or methyl ethyl ketone (MEK). Isopropyl rubbing alcohol should be avoided. Application method will determine how much you need to thin LMM-6000. When spraying we recommend a 1:1 mix of LMM-6000 to ethanol, by volume. MEK and acetone are stronger solvents, so you will need less thinner if using these. When applying with foam brush we recommend a 2:1 ratio to start, 2 parts ethanol to 1 part LMM-6000 by volume, add more ethanol as needed. Keep in mind that the more the material is thinned, the less active ingredients are being applied. If LMM-6000 is thinned too much, the mark may appear to be lighter in color than what the LMM-6000 could produce. Clean the surface of the metal so it is free of any type of lubricants or oils. Apply a thin coat of LMM-6000 to the metal; try to apply an even coating. LMM-6000 can be applied by a spray gun, air brush, paint brush or a foam brush. If the material is applied too thin, the mark will not be as dark. If the material is applied too thick, it will require more power to make the mark. It is important that LMM-6000 is applied with an even and thin coat. Applying LMM-6000 may require practice to achieve the right coverage. We recommend that all CerMark LMM products be applied in a well-ventilated area or spray booth designed to pull air away from user. It is important that the LMM-6000 is allowed to dry thoroughly. It can air dry in about 2 minutes. This process can be sped up by using a drying oven, hair dryer or a heat lamp. Laser power and speed settings vary greatly based on the size and power level of the laser system used. Each customer will have to develop settings for there system. After laser marking excess material can be removed by washing with warm water in a sink or wet paper towels. These products are only meant for marking directly on metal. Paint or other coatings can prevent the material from bonding correctly.
The CerMark LMM 6000 coating creates permanent black laser marks on hard metal types such as Stainless Steel. CerMark LMM 6000 will work with CO2 lasers with 30 or more watts of power and fiber lasers that can reach a frequency of 200 kHz. or higher. LMM 6000 will work on some aluminum grades but much slower marking speed is required. LMM 6000 is NOT recommended for Chrome or softer metals like Brass, Copper and Pewter. CerMark LMM 14 is recommended for chrome and softer metals. For best results apply with an air brush. A foam brush should be used if not spraying. LMM-6000 is formulated thick to prevent settling. It may be necessary to thin the paste before using. We recommend thinning with ethanol, denatured alcohol, acetone or methyl ethyl ketone (MEK). Isopropyl rubbing alcohol should be avoided. Application method will determine how much you need to thin LMM-6000. When spraying we recommend a 1:1 mix of LMM-6000 to ethanol, by volume. MEK and acetone are stronger solvents, so you will need less thinner if using these. When applying with foam brush we recommend a 2:1 ratio to start, 2 parts ethanol to 1 part LMM-6000 by volume, add more ethanol as needed. Keep in mind that the more the material is thinned, the less active ingredients are being applied. If LMM-6000 is thinned too much, the mark may appear to be lighter in color than what the LMM-6000 could produce. Clean the surface of the metal so it is free of any type of lubricants or oils. Apply a thin coat of LMM-6000 to the metal; try to apply an even coating. LMM-6000 can be applied by a spray gun, air brush, paint brush or a foam brush. If the material is applied too thin, the mark will not be as dark. If the material is applied too thick, it will require more power to make the mark. It is important that LMM-6000 is applied with an even and thin coat. Applying LMM-6000 may require practice to achieve the right coverage. We recommend that all CerMark LMM products be applied in a well-ventilated area or spray booth designed to pull air away from user. It is important that the LMM-6000 is allowed to dry thoroughly. It can air dry in about 2 minutes. This process can be sped up by using a drying oven, hair dryer or a heat lamp. Laser power and speed settings vary greatly based on the size and power level of the laser system used. Each customer will have to develop settings for there system. After laser marking excess material can be removed by washing with warm water in a sink or wet paper towels. These products are only meant for marking directly on metal. Paint or other coatings can prevent the material from bonding correctly.
LaserSketch provides the finest Absolute Black Marble and Super Black Granit Blanks for the Photo Lasering Imdustry. A long with Laserable Jewelry and
CerMark LMM6000.500: Black, 500 gram (paste), liquid for Metal Marking, High Stick Compound for Brightly Polished Metals
CerMark LMM-6000 Aerosol – Laser Jump Start
Cermark LMM6000 for Stainless
CerMark LMM 6000 Black for Metal – 1,000 Grams Concentrated Liquid – CerMark Sales
The CerMark LMM 6000 coating creates permanent black laser marks on hard metal types such as Stainless Steel. CerMark LMM 6000 will work with CO2
CerMark LMM 6000 Black for Metal – 1,000 Grams Concentrated Liquid
Weight: 1.00 lbs, GSLA_LMM-6000 Black Aerosol Spray Can, Shipping Note: This product uses an aerosol can and cannot be shipped via UPS/FedEx Air.
Cermark LMM 6000, Aerosol (1Can,12oz)
CerMark LMM-6000 Aerosol – Laser Jump Start
CerMark LMM-6000 Metal Marking Solution - Black - 500 grams
CerMark LMM-6000 is used to add black permanent laser engraved markings to hard metals such as Stainless Steel This listing is for a 12oz aerosol can
CerMark LMM6000 12oz Aerosol - Cermark Metal Laser Marking Spray - Laser Engraver Engraving Machine Blanks
CerMark LMM-6000 Metal Marking Solution - Black - 500 grams
CerMark LMM-6000 Metal Marking Solution - Black - 500 grams
CerMark LMM 6000 Black for Metal – 1,000 Grams Concentrated Liquid
CerMark LMM-6000 Metal Marking Solution - Black - 500 grams
CerMark LMM6000 12oz Aerosol - Cermark Metal Laser Marking Spray - Laser Engraver Engraving Machine Blanks
CerMark LMM 14 Black for Metals – 500 Grams Liquid – CerMark Sales
Recommended for you
-
CerMark LMM 6000 Black for Metal – 12oz Aerosol Spray15 May 2024
-
Which Metal Marking Spray works better for Laser Engraving15 May 2024
-
Cermark Metal Marking15 May 2024
-
Laser Marking Solutions15 May 2024
-
Cermark Laserable Metal Marking Paste (LMM6000)15 May 2024
-
CerMark Ultra 12 OZ Spray Can15 May 2024
-
Laser Marking, Engraving, CerMark TherMark - Cermark USA15 May 2024
-
2 Pack CERMARK ULTRA SPRAY FOR LASER MARKING - 12OZ15 May 2024
-
Laser Marking, Dyes, Produkte15 May 2024
-
Cermark® & Thermark® - Black marking solution15 May 2024
You may also like
-
What are the best pens to be used for creating zentangle art? - Quora15 May 2024
-
6 Packs: 30 ct. (180 total) Cricut® Infusible Ink™ Ultimate Marker Set15 May 2024
-
→ Guillotinas de papel La tienda Nº1 para comprar tu guillotina15 May 2024
-
Double Sided Tape Heavy Duty, Waterproof Mounting Foam Tape, 16.415 May 2024
-
PigPotParty 6x 9, 100Pcs Bottom Gusset Bags, Clear Plastic Cellophane Treat Goodie Bags with Ties for Party Favor, Candy, Cookie, Popcorn, Small15 May 2024
-
Cartoon hospital room with medieval decor for visual novel on Craiyon15 May 2024
-
WARNING! WAX MELT - Packing Stickers / Labels - Available In 3 sizes £7.51 - PicClick UK15 May 2024
-
EVA Foam Sheets 35x50cm 35x100cm Handmade DIY Craft Cosplay Model 1~10mm15 May 2024
-
Artist Vine Charcoal Sticks Medium Black Sketch Charcoal Pencils for Kids Adults Drawing Sketching Fine Art 25pcs15 May 2024
-
Add-a-patch Extreme Magnetic Morale Patch Holder With Loop Velcro and Neodymium Magnets, 4 Sizes: 2x2, 2x3, 3x4 & 3 Circle15 May 2024