FashionFlex Puff HTV Metallic Red 12x20 –
By A Mystery Man Writer
Last updated 03 Jun 2024
Add a fun 3D look to any design with FashionFlex® Puff! FashionFlex® Puff is a brand new puff product line available in 14 colors- the most puff colors in the industry! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy
Add a fun 3D look to any design with FashionFlex® Puff! FashionFlex® Puff is a brand new puff product line available in 14 colors- the most puff colors in the industry! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy repositioning. Results will vary depending on the material it is applied to. Application Instructions Blade – 45° Cut – Mirror image Temp – All colors:255°F – *275°FVary Puff effect by increasing or decreasing temperature by 10°F within range.*Metallic: 275°F Pressure – Medium, even Time – 12-14 secondsStart at 12.If more time is needed, press an additional 2 seconds.Metallic: 10 seconds. Peel – Peel hot.Remove the carrier and/or transfer sheet immediately.Metallic: Re-press for 4 seconds for maximum puff. *We personally found (for metallic only) that doing 275 for 10 seconds, peeling cover sheet, then repressing for 10 seconds worked the best for us. CARE – Wash inside out, cold water, gentle cycle, tumble dry low. Applies to: Cotton, Uncoated Polyester, Fabric Blends, Polyester/Acrylic, and Similar Fabrics Excluding Nylon Special Precautions Cannot be layered. Remove carrier immediately after pressing. If the carrier or transfer sheet is left on, it can create inconsistencies in the puffed material. Color variation - During manufacturing, color variation can occur between rolls. This is especially true for Neon colors. CUT SETTINGS PLEASE NOTE: Every blade and machine is a little bit different- always remember to test cut! These cut settings are a starting point to be adjusted to your blade and machine. CRICUT Material: Iron-On Pressure: Default Blade: Fine-Point Blade SILHOUETTE Material: Heat Transfer, Smooth Blade: 3 Speed: 8 Force: 10 GRAPHTEC Speed: 8 Force: 18 We use a 45° blade. Clear plastic side needs to be face down while cutting. Peel up a corner of the carrier to determine this before cutting. Carrier can be shiny or matte depending on batch. Size is +/- 0.50 inch and +/-3% on length Colors of products may be different than what the screen on your device shows. TIP: Always perform a test cut prior to cutting a whole design Helpful tip-Specialty Materials recommends if your T shirt or material your are putting this HTV on says dry fit, Moisture Wicking, or is Gildan Ultra Cotton, use a spray bottle of rubbing alcohol and squirt the material where you are putting the design. Then rub it in a bit with a cloth and dry or even heat press it to dry then press the design. This is due to the material being a coated material, instead of an un coated material.
Add a fun 3D look to any design with FashionFlex® Puff! FashionFlex® Puff is a brand new puff product line available in 14 colors- the most puff colors in the industry! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy repositioning. Results will vary depending on the material it is applied to. Application Instructions Blade – 45° Cut – Mirror image Temp – All colors:255°F – *275°FVary Puff effect by increasing or decreasing temperature by 10°F within range.*Metallic: 275°F Pressure – Medium, even Time – 12-14 secondsStart at 12.If more time is needed, press an additional 2 seconds.Metallic: 10 seconds. Peel – Peel hot.Remove the carrier and/or transfer sheet immediately.Metallic: Re-press for 4 seconds for maximum puff. *We personally found (for metallic only) that doing 275 for 10 seconds, peeling cover sheet, then repressing for 10 seconds worked the best for us. CARE – Wash inside out, cold water, gentle cycle, tumble dry low. Applies to: Cotton, Uncoated Polyester, Fabric Blends, Polyester/Acrylic, and Similar Fabrics Excluding Nylon Special Precautions Cannot be layered. Remove carrier immediately after pressing. If the carrier or transfer sheet is left on, it can create inconsistencies in the puffed material. Color variation - During manufacturing, color variation can occur between rolls. This is especially true for Neon colors. CUT SETTINGS PLEASE NOTE: Every blade and machine is a little bit different- always remember to test cut! These cut settings are a starting point to be adjusted to your blade and machine. CRICUT Material: Iron-On Pressure: Default Blade: Fine-Point Blade SILHOUETTE Material: Heat Transfer, Smooth Blade: 3 Speed: 8 Force: 10 GRAPHTEC Speed: 8 Force: 18 We use a 45° blade. Clear plastic side needs to be face down while cutting. Peel up a corner of the carrier to determine this before cutting. Carrier can be shiny or matte depending on batch. Size is +/- 0.50 inch and +/-3% on length Colors of products may be different than what the screen on your device shows. TIP: Always perform a test cut prior to cutting a whole design Helpful tip-Specialty Materials recommends if your T shirt or material your are putting this HTV on says dry fit, Moisture Wicking, or is Gildan Ultra Cotton, use a spray bottle of rubbing alcohol and squirt the material where you are putting the design. Then rub it in a bit with a cloth and dry or even heat press it to dry then press the design. This is due to the material being a coated material, instead of an un coated material.
20 PerfecPress Foam/Puff HTV Sheets
FashionFlex Puff 19.5 By-The-Foot Heat Transfer Vinyl
FASHIONFlex®PUFF – Specialty Materials
Shop for Fashion Flex Puff Vinyl at Sign Outlet Store
Fashionflex Puff 12 X 19.5 / 1 Sheet / HTV Heat Transfer Vinyl HTV
FashionFlex®
Fashionflex Puff 12 X 19.5 / 1 Sheet / HTV Heat Transfer Vinyl HTV
WRAPXPERT Puff Vinyl Heat Transfer Black 3D Puffy HTV
Specialty Materials Metallic FashionFlex Puff HTV From Creative
Specialty Materials FashionFlex Puff - Wholesale Heat Transfer
Shop for Fashion Flex Puff Vinyl at Sign Outlet Store
FashionFlex Puff HTV White 12x20 –
Recommended for you
-
Tintnut Puff Vinyl Heat Transfer - 11 Sheets 12 x 10inches 3D Puff03 Jun 2024
-
Puff Heat Transfer Vinyl 12 x 20 – Jerosa Designs LLC03 Jun 2024
-
TransWonder Red Puff Vinyl Heat Transfer - 3D Puff Heat Transfer Vinyl HTV Puff Vinyl 12x6' for Heat Press T Shirt Compatible with Cricut Air or03 Jun 2024
-
HT Puff Heat Transfer Vinyl 20 Width Roll03 Jun 2024
-
#1045 Red Puff Vinyl T-shirt/Sweatshirt | Forever Designs, LLC03 Jun 2024
-
Be Mine Puff Vinyl – twistedtrail03 Jun 2024
-
Monochromatic Ricebird Varsity Puff VInyl Sweatshirt – Marie & Company03 Jun 2024
-
3D Puff Heat Transfer Vinyl, Puffy HTV03 Jun 2024
-
HTV PUFF VINYL (Walakut puff vinyl) REVIEW03 Jun 2024
-
Fashion Flex Puff HTV - Red Puff Heat Transfer Vinyl03 Jun 2024
You may also like
-
Acrylic Keychain Blanks 2.5, 20 Set Clear Key Chain with Open Jump Ring03 Jun 2024
-
Lorene Wool Wash Mitt03 Jun 2024
-
Arabian Vanilla Premium Oil Perfume, Attar - Full Strength03 Jun 2024
-
Picture Frame Mat Dark Green With Gold Liner 11x14 for 8x10 Photo or Diploma Size Rectangle Cutout03 Jun 2024
-
25 Books All Women Should Read in Their Lifetime03 Jun 2024
-
Custom Metal Stamp for Metal Stamping Punch Stamp | Metal Punch Stamp Jewelry Stamp | Metal Logo Stamp | Metal Stamp Designs | Steel Stamp | Metal03 Jun 2024
-
WUTA New Fabric Cutting Mat, Leather Cutting Board A1 A2 A3 A4 A503 Jun 2024
-
1pc yellow creative cartoon pen bag, students can use pencil bag cute pencil case03 Jun 2024
-
JAZUIHA Jazuiha Earrings Organizer 5-Layer 100 Holes Ear Stud Holder Earring Display Stand Wooden Base Jewelry Organizer For Hanging Ear03 Jun 2024
-
Specialist Silicone Spray 100 ml03 Jun 2024