FashionFlex Puff HTV Red 12x20 –
By A Mystery Man Writer
Last updated 04 Jun 2024
Add a fun 3D look to any design with FashionFlex® Puff! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy repositioning. Results will vary depending on the material it is applied to. Application Instructions Blade – 45°
Add a fun 3D look to any design with FashionFlex® Puff! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy repositioning. Results will vary depending on the material it is applied to. Application Instructions Blade – 45° Cut – Mirror image Temp – All colors:255°F – *275°FVary Puff effect by increasing or decreasing temperature by 10°F within range.*Metallic: 275°F Pressure – Medium, even Time – 12-14 secondsStart at 12.If more time is needed, press an additional 2 seconds.Metallic: 10 seconds. Peel – Peel hot.Remove the carrier and/or transfer sheet immediately.Metallic: Re-press for 4 seconds for maximum puff. *We personally found (for metallic only) that doing 275 for 10 seconds, peeling cover sheet, then repressing for 10 seconds worked the best for us. CARE – Wash inside out, cold water, gentle cycle, tumble dry low. Applies to: Cotton, Uncoated Polyester, Fabric Blends, Polyester/Acrylic, and Similar Fabrics Excluding Nylon Special Precautions Cannot be layered. Remove carrier immediately after pressing. If the carrier or transfer sheet is left on, it can create inconsistencies in the puffed material. Color variation - During manufacturing, color variation can occur between rolls. This is especially true for Neon colors. CUT SETTINGS PLEASE NOTE: Every blade and machine is a little bit different- always remember to test cut! These cut settings are a starting point to be adjusted to your blade and machine. CRICUT Material: Iron-On Pressure: Default Blade: Fine-Point Blade SILHOUETTE Material: Heat Transfer, Smooth Blade: 3 Speed: 8 Force: 10 GRAPHTEC Speed: 8 Force: 18 We use a 45° blade. Clear plastic side needs to be face down while cutting. Peel up a corner of the carrier to determine this before cutting. Carrier can be shiny or matte depending on batch. Size is +/- 0.50 inch and +/-3% on length Colors of products may be different than what the screen on your device shows. TIP: Always perform a test cut prior to cutting a whole design Helpful tip-Specialty Materials recommends if your T shirt or material your are putting this HTV on says dry fit, Moisture Wicking, or is Gildan Ultra Cotton, use a spray bottle of rubbing alcohol and squirt the material where you are putting the design. Then rub it in a bit with a cloth and dry or even heat press it to dry then press the design. This is due to the material being a coated material, instead of an un coated material.
Add a fun 3D look to any design with FashionFlex® Puff! This is super easy to use as you only need to press once to get that puff effect. It’s easy to weed and its pressure-sensitive carrier allows for easy repositioning. Results will vary depending on the material it is applied to. Application Instructions Blade – 45° Cut – Mirror image Temp – All colors:255°F – *275°FVary Puff effect by increasing or decreasing temperature by 10°F within range.*Metallic: 275°F Pressure – Medium, even Time – 12-14 secondsStart at 12.If more time is needed, press an additional 2 seconds.Metallic: 10 seconds. Peel – Peel hot.Remove the carrier and/or transfer sheet immediately.Metallic: Re-press for 4 seconds for maximum puff. *We personally found (for metallic only) that doing 275 for 10 seconds, peeling cover sheet, then repressing for 10 seconds worked the best for us. CARE – Wash inside out, cold water, gentle cycle, tumble dry low. Applies to: Cotton, Uncoated Polyester, Fabric Blends, Polyester/Acrylic, and Similar Fabrics Excluding Nylon Special Precautions Cannot be layered. Remove carrier immediately after pressing. If the carrier or transfer sheet is left on, it can create inconsistencies in the puffed material. Color variation - During manufacturing, color variation can occur between rolls. This is especially true for Neon colors. CUT SETTINGS PLEASE NOTE: Every blade and machine is a little bit different- always remember to test cut! These cut settings are a starting point to be adjusted to your blade and machine. CRICUT Material: Iron-On Pressure: Default Blade: Fine-Point Blade SILHOUETTE Material: Heat Transfer, Smooth Blade: 3 Speed: 8 Force: 10 GRAPHTEC Speed: 8 Force: 18 We use a 45° blade. Clear plastic side needs to be face down while cutting. Peel up a corner of the carrier to determine this before cutting. Carrier can be shiny or matte depending on batch. Size is +/- 0.50 inch and +/-3% on length Colors of products may be different than what the screen on your device shows. TIP: Always perform a test cut prior to cutting a whole design Helpful tip-Specialty Materials recommends if your T shirt or material your are putting this HTV on says dry fit, Moisture Wicking, or is Gildan Ultra Cotton, use a spray bottle of rubbing alcohol and squirt the material where you are putting the design. Then rub it in a bit with a cloth and dry or even heat press it to dry then press the design. This is due to the material being a coated material, instead of an un coated material.
FASHIONFlex®PUFF – Specialty Materials
Add a fun 3D look to any design with FashionFlex® Puff!, This is super easy to use as you only need to press once to get that puff effect. It’s easy
FashionFlex Puff HTV Emerald Green 12x20
HTV | Craft Packs | 3D Puff (02) Black / 3- 10 x 12 Sheets
WRAPXPERT Puff Vinyl Heat Transfer Black 3D Puffy HTV Iron on Vinyl for Tshirts,Easy Cut/Weed Foaming HTV Roll for Heat Press,Clothing,10x5ft
WRAPXPERT Puff Vinyl Heat Transfer Black 3D Puffy HTV Iron on Vinyl for Tshirts,Easy Cut/Weed Foaming HTV Roll for Heat Press,Clothing,10x5ft
DecoFilm Glitter Chameleon HTV-Blue Choose Your Length SALE While Supp –
FashionFlex Puff HTV Metallic Red 12x20 –
USD-500-$5.00-$5.00 USD-5.00
Pink / 12x20 Sheet
Even in your most intricate designs, 3D PUFF Vinyl sheets are easy to weed. Remove unnecessary vinyl with ease whether it's small letters or tiny
3D Puff Heat Transfer Vinyl - 20 x 36 (1 Yard) (Puff Red)
Puff Vinyl
FashionFlex Puff (Neon Orange)
Recommended for you
-
Siser Easy Puff HTV 11.8x1yd - Puffy Heat Transfer Vinyl (White) - Compatible with Siser, Cricut, and Silhouette Cutters – CPSIA Certified04 Jun 2024
-
3D PUFF HTV, 180 Colored Puff Vinyl, Puff Heat Transfer Vinyl - 12x10 PUFF HTV04 Jun 2024
-
3D Puff HTV Vinyl04 Jun 2024
-
Sale* Puff HTV 12×5 Foot Rolls04 Jun 2024
-
Heat Transfer Vinyl 4U HT Puff Heat Transfer Vinyl 20 inch (Apple Green, 1 Foot), 20 Inchesx 1 Foot04 Jun 2024
-
3D Puff HTV Heat Transfer Vinyl Film Glow in The Dark Luminous Iron on;Cricula~04 Jun 2024
-
Puff HTV Heat Transfer Vinyl 3D Foamed Iron on Transfers, Heflashor Assorted 8 Solid Colors Puff HTV Vinyl Heat Transfer 12 x 10 PU HTV Easy Cut Weed Iron on Vinyl04 Jun 2024
-
Patriots School Spirit Puff/HTV Transfer – Hernandez Homemade Blanks & More04 Jun 2024
-
WALAKut Puff HTV Tips and Tricks04 Jun 2024
-
Siser Easy Puff - HTV 12 x 1 Yd. – Melissa's Vinyl Supply04 Jun 2024
You may also like
-
Rickrack Quilt Pattern by Missouri Star04 Jun 2024
-
best makeup beauty mommy blog of india: Best Rose Petal Powder for Face ft. Stamio04 Jun 2024
-
10 Pcs Rainbow Canvas Makeup Bags Bulk Inspirational Quotes04 Jun 2024
-
Grumbacher Mixed Media Paper Pad with In & Out Pages, 60 Sheet04 Jun 2024
-
Koala Ultra Premium Photo Paper 5x7 in Satin Photo Printer Paper for Inkjet Printer Water-Resistant Semi Gloss 50 Sheets 72lb, Size: 5 x 7, White04 Jun 2024
-
12ct Curly Bows Silver & Gold – WrapaholicGifts04 Jun 2024
-
Rainbow Scratch Paper Art Set,59 PCS Black Drawing Paper Off Art Craft – ToysCentral - Europe04 Jun 2024
-
MAS Table Top Pro Epoxy - 2 Quart - Reviews04 Jun 2024
-
Homz Clear Plastic 3-drawer Medium Home Organization Storage04 Jun 2024
-
NHance Hair Fiber Spray Kit by The Rich Barber, Set Includes Thickening Fibers, Hold Spray, Applicator & Application Card04 Jun 2024