Hydrostone 25 Lbs - Free Shipping – WORKSHOP HERITAGE

USG Hydro-Stone® Brand Gypsum Cement is an excellent product for manufacturing solid cast architectural, art novelty and statuary products. USG Hydro-Stone Gypsum Cement is extremely hard, has high compressive strength, and has high water absorption resistance while giving extremely fine detail duplication. MIXING INST

USG Hydro-Stone® Brand Gypsum Cement is an excellent product for manufacturing solid cast architectural, art novelty and statuary products. USG Hydro-Stone Gypsum Cement is extremely hard, has high compressive strength, and has high water absorption resistance while giving extremely fine detail duplication.

MIXING INSTRUCTIONS

Use potable water at temperatures between 70 °F (21 °C) and 100 °F (38 °C). Because variations in slurry (USG Hydro-Stone Gypsum Cement and water mixture) temperature produce variations in set time, it is important to keep both the USG Hydro-Stone Gypsum Cement and water in a stable temperature environment prior to use. The higher the temperature of the slurry, the shorter the set time. Conversely, the lower the temperature of the slurry, the longer the set time.

Weigh both the USG Hydro-Stone Gypsum Cement and the water prior to use for each mix. The water-to-USG Hydro-Stone Gypsum Cement ratio is critical because it governs the strength and the density of the final cast.

Sift or strew USG Hydro-Stone Gypsum Cement into the water slowly and evenly. Do not drop large amounts of USG Hydro-Stone Gypsum Cement directly into the water as proper soaking of the USG Hydro-Stone Gypsum Cement may not occur. USG Hydro-Stone Gypsum Cement should be fully dispersed in the water prior to mixing. Small batches require less soaking time than large batches. See USG IG503 Plaster Mixing Procedures for specific soaking instructions.

Mixing USG Hydro-Stone Gypsum Cement slurry is one of the most important steps in producing USG Hydro-Stone Gypsum Cement casts with maximum strength, absorption, hardness and other important properties.

Mechanically mixed slurries develop uniform casts with optimal strengths. USG Hydro-Stone Gypsum Cement can be mechanically mixed through both batch and continuous processes. Proper blade and bucket dimensions are important for obtaining the best batch mix (see USG IG503 Plaster Mixing Procedures for details).

Longer mixing times result in higher mold strength and shorter set times.

POURING

To prevent air entrainment and provide a uniform, smooth surface, careful pouring of USG Hydro-Stone Gypsum Cement slurry is necessary. Agitation/vibration of the filled mold is a further step used to prevent air at or near the mold surface. Whenever possible, USG Hydro-Stone Gypsum Cement slurry should be poured carefully in the deepest area so that the slurry flows evenly across the surface of the case mold.

Pouring a large amount of slurry directly on the face of the case mold may result in slight densification of the USG Hydro-Stone Gypsum Cement mold at the point where it strikes the surface of the case. This produces a hard spot, giving uneven absorption.

DRYING

All casts should be dried as quickly as is safely possible after manufacture so that maximum physical properties can develop. Dry to a constant weight.

The best drying rooms or ovens provide 1) uniform and rapid circulation (minimum of 15-30 fps (4.6-9.1 mps)) of air with no “dead spots” having little or no air movement, 2) equal temperatures throughout the entire area, and 3) provisions for exhausting a portion of the air while replacing it with fresh air. High humidity surrounding the drying room or oven inhibits drying efficiency because the air pulled into the room is incapable of picking up much moisture from the molds.

The maximum temperature at which USG Hydro-Stone Gypsum Cement molds are safe from calcination is 120 °F (49 °C). With substantial free water in the mold, a higher drying temperature can be used without difficulty. As drying progresses, the temperature must be reduced to prevent calcination. Before removing molds from the dryer, the temperature should approach that of the area around the dryer to prevent thermal shock. See IG502 Drying Plaster Casts for additional information.

STORAGE AND USE

When properly used, USG Hydro-Stone Gypsum Cement is easy to work with and complies with the federal Labeling of Hazardous Art Materials Act, 12 U.S.C. Section 1277 and ASTM D4236. Keep indoors at temperatures between 65 °F - 75 °F (18 °C - 24 °C) and 45% - 55% RH. Do not stack more than two pallets high. Keep from drafts. Rotate stock. USG Hydro-Stone Gypsum Cement should be used within 6 months of the manufacturing date located on the package. Always follow handling and use directions and safety warnings on the package.

Information listed from USG Hydrostone manufacturer website

All Soap Making Products, Cutters, Molds, Colorants

All Soap Making Products, Cutters, Molds, Colorants

CREEKSTONE 264 GPH Submersible Pond Pump for $19.99 – Harbor Freight Coupons

BORIDE Mold Polishing Stone Kits - BORIDE Engineered Abrasives

Halsey Taylor Hydroboost Bottle Filling Stations for Sale

Soap Making Supplies, Molds, Cutters

Pro-Soaper All-in-One Tall Skinny Standard and Slab Mold - MADE IN USA – WORKSHOP HERITAGE

Project Source 20-ft x 16-ft Blue Waterproof Standard Polyethylene 5-mil Tarp in the Tarps department at

Outdoor Bottle Filling Stations ideal for educational campuses and recreational areas. Powder-coated exterior over a corrosion-resistant stainless steel type-316 base material to provide protection from the elements. Corrosion-resistant base material provides the ultimate protection from the elements. Heavy-gauge construction with tamper-resistant screws that resist stains and corrosion.

Elkay LK4420BF1UFRKEVG Outdoor Bottle Filling Station & Drinking Fountain - Non Refrigerated, Evergreen

Floor Standing Bottleless Water Cooler