Rubber Bumper Body Grommet and Hole Plug Kit

By A Mystery Man Writer

Last updated 09 Jun 2024

Rubber Bumper Body Grommet and Hole Plug Kit

Rubber Bumper Grommet and Hole Plug Kit 240Z - 650-204 (). We put together this 17 piece kit to help simplify getting all of the rubber hole plugs and bumpers you will need when painting a car and replacing these items.

We put together this kit to help simplify getting all of the rubber hole plugs and bumpers you will need when painting a car and replacing these items. There is a kit for 70-74, 75-76 an 77-78. Genuine Nissan parts are used where available. Depending on the extent of your restoration you may need more of the round plugs but this kit will get you started. Kit includes the following:

(2) 200-815 Rubber hatch jamb plug

(2) 200-762 Rubber Floor pan plug

(1) 200-807 Spare tire area floor plug

(2) 200-450 Door Bumper (200-451 for 77-78)

(1) 200-415 Hood to fender stops

(1) 200-444 Hatch stops

(1) 200-457 Floor pan hole plugs

(2) 200-458 Hatch hole plugs

(1) 200-461 Wiper shaft seals

(1) 200-521 Inspection door seals

(1) 200-414 Inspection lid bumpers (300-036 for 77-78)

(1) 200-411 Adjustable hood stops

(1) 200-501 Gas Lid door bumpers

Search the PT# for a description of each individual item.

New fuel tank sending unit for 1970-1974 Datsun 240Z and 260Z as well as 75-76 280Z*. Choose from OEM Nissan or aftermarket part. If your fuel gauge is not working or working erratically, the fuel sender is most likely the problem. Installs in the front passenger side of the fuel tank. Removal of the tank should not be required to install the sender. Just be sure your gas tank is close to empty before removing the old sending unit.

1977-78 280Z uses the sending unit that drops in the top of the tank, 3 wire connector.

Aftermarket unit includes O-ring, OEM does not include O-ring.

*75-76 280Z has a 3 wire connector for the sending unit, the 240Z sender only uses 2 wires. Use your solid yellow and black wire from the 280Z harness to connect to this sender. Low fuel light (if applicable) may not function with this sender.

Connector PT# 800-1124, O-ring PT# 200-409.

New OEM Genuine Nissan rubber inner shift boot. This rubber shift boot will fit 1972-78 Datsun 240Z, 260Z, and 280Z (not series 1). This inner shift boot fits on the metal floor tunnel which is right below the vinyl or leather shift boot. This rubber boot helps to keep out noise, fumes, and debris that can come in from underneath the car.

*See PT# 800-1233 for metal retainer plate for this boot.

New coolant thermostat in 160, 170, 180 or 195 degree. Will fit datsun 240Z, 260Z, 280Z, 280ZX and 510 1968-83. The 160 thermostat is the lowest temperature available. This thermostat will help your engine run cooler or great for racing engines. However in the winter this 160 thermostat may not allow your heater to blow hot air. A 180 is the best of both worlds and if you are in a year round cool climate the 195 is best.

Three styles available:

-Standard replacement

-High Flow

-Fail Safe.. If thermostat fails it goes to full open instead of closing and overheating the engine.

New OEM genuine Nissan shifter bushing kit. Includes all the parts needed to restore your shifter to its original tight feel. This kit will fit Datsun 240Z, 260Z, 280Z, and 280ZX, from Aug 1971 to 1983. Parts included are the shifter metal pin with both plastic bushings and the E clip, along with the shifter end cup bushing. These parts are serviceable from the interior of the car, under the shift boot. Choose from two different options.

* Individual parts are sold separately on the website.

New OEM Genuine Nissan oil filter for Datsun 240Z, 260Z, 280Z, 280ZX and 510, 1969-83. Made in japan.

1 3/8 Firewall Rubber Hole Plugs with Compression Stem - Push-In Compression Stem - Bulkhead Plugs These hole plugs are attached without need for