WOD Kapton Tape 2 Mil, Ships Today - Multiple Sizes - Tape Providers

By A Mystery Man Writer

Last updated 17 Jun 2024

WOD Kapton Tape 2 Mil, Ships Today - Multiple Sizes - Tape Providers

Polyimide Film Tape is a 2 mil electrical grade coated with a high performance silicone adhesive. It is a wave solder/hot air leveling tape used to protect gold contacts on printed circuit boards from molten solder during hot air wave solder leveling process. Available in Multiple Sizes.
Kapton Polyimide Film TapesProduct DescriptionWOD PKT2 Kapton™ Polyimide Film Tape is a 2 mil electrical grade Kapton alternative POLYIMIDE film coated with a high performance silicone adhesive. It is a wave solder/hot air leveling tape used to protect gold contacts on printed circuit boards from molten solder during hot air wave solder leveling process. It is thin and conformable, with outstanding tear and abrasion resistance at elevated temperatures. Adhesive will thermoset to increase adhesion values.WOD PKT2 Leaves minimal residue when removed after manufacturing process; reduces clean-up time and minimizes rejects. Permits observation of board during processing. Kapton Electrical Grade/Printed Circuit Polyimide Film Tape has excellent resistance to acids, oils, solvents, aging, staining and water immersion.The Adhesive Employs a proprietary technology that results in extremely low electrostatic discharge at unwind and removal from the PWB. Conventional polyimide tapes can typically generate over 10,000 volts during use which can damage board mounted electronic components. WOD tape PKT2 overcomes this problem without any of the typical drawbacks of conventional "anti-static" or "static-free" tapes (e.g., variable adhesion and opaqueness).Product ApplicationsPrimarily used in electrical insulation and gold finger protection.Protects gold tabs in circuit boards during soldering.Protects surfaces helping reduce replacement partsUsed in electrical applications such as harness/coil wraps & separators, transformers & slot liners where good insulation & heat resistance are required.electrical insulation applications this product does meet class H requirementsTechnical PropertiesAdhesive: High performance siliconeCarrier/Backing: Electrical grade polyimide filmThickness: 3.5 mils (carrier, adhesive)Adhesion: 27.4 ounces per inch (to stainless steel test panel)Tensile Strength: > 36.5 pounds per inch (longitudinal)Dielectric Strength: > 8,000 voltsElongation: > 70%Service/Operating Temperature: up to 392°FSpecification Met: MIL-P-46112B; UL510 approved for flame retardanceCore: 3" DiameterAdditional InformationAlternative to: Electro Tape 95-2; Ideal 9322; T&F 3903; American 304-2; Anchor K-350; Permacel P-222; Taconic 6325-02; Berry Plastics 2345-2; Tesa 4429; Dewal 303-2.Note: Specifications are those given by manufacturers and are not tested for accuracy.

Kapton Polyimide Film Tapes

Product Description

WOD PKT2 Kapton™ Polyimide Film Tape is a 2 mil electrical grade Kapton alternative POLYIMIDE film coated with a high performance silicone adhesive. It is a wave solder/hot air leveling tape used to protect gold contacts on printed circuit boards from molten solder during hot air wave solder leveling process. It is thin and conformable, with outstanding tear and abrasion resistance at elevated temperatures. Adhesive will thermoset to increase adhesion values.

WOD PKT2 Leaves minimal residue when removed after manufacturing process; reduces clean-up time and minimizes rejects. Permits observation of board during processing. Kapton Electrical Grade/Printed Circuit Polyimide Film Tape has excellent resistance to acids, oils, solvents, aging, staining and water immersion.

The Adhesive Employs a proprietary technology that results in extremely low electrostatic discharge at unwind and removal from the PWB. Conventional polyimide tapes can typically generate over 10,000 volts during use which can damage board mounted electronic components. WOD tape PKT2 overcomes this problem without any of the typical drawbacks of conventional anti-static or static-free tapes (e.g., variable adhesion and opaqueness).

Product Applications

Primarily used in electrical insulation and gold finger protection.
Protects gold tabs in circuit boards during soldering.
Protects surfaces helping reduce replacement parts
Used in electrical applications such as harness/coil wraps & separators, transformers & slot liners where good insulation & heat resistance are required.
electrical insulation applications this product does meet class H requirements

Technical Properties

Adhesive: High performance silicone
Carrier/Backing: Electrical grade polyimide film
Thickness: 3.5 mils (carrier, adhesive)
Adhesion: 27.4 ounces per inch (to stainless steel test panel)
Tensile Strength: > 36.5 pounds per inch (longitudinal)
Dielectric Strength: > 8,000 volts
Elongation: > 70%
Service/Operating Temperature: up to 392°F
Specification Met: MIL-P-46112B; UL510 approved for flame retardance
Core: 3 Diameter

Additional Information

Alternative to: Electro Tape 95-2; Ideal 9322; T&F 3903; American 304-2; Anchor K-350; Permacel P-222; Taconic 6325-02; Berry Plastics 2345-2; Tesa 4429; Dewal 303-2.

Note: Specifications are those given by manufacturers and are not tested for accuracy.