Paasche Air Eraser Kit (ready to plug into air compressor
By A Mystery Man Writer
Last updated 18 Jun 2024
Paasche Air Eraser kit with connectors to plug straight into your air compressor. The Paasche air eraser can be used for fossil preparation, etching and for cleaning surfaces and jewellery. Free samples of aluminium oxide and dolomite powder.
The Paasche AEC Air Eraser is an entry-level air abrasive that is widely used in fossil preparation. The powder is held in the little cup on top and blasted through a tungsten carbide nozzle when you depress the button on top. This powder flow stops when the button is released.We have put together a kit so that it is ready to plug straight into your air compressor and get going!In this kit:Paasche Air EraserAdaptors2m Festo Air HoseQuick connector (PCL/Euro as per user requirements)FREE 100g sample of Aluminium Oxide powderFREE 100g sample of Dolomite powderOptional Sparmax Silver Bullet Plus with Bleed Valve Moisture Trap.For general work, use clean dry air at pressures of 2-3 Bars (30-45 PSI), going up to a maximum of 4.5 Bars (65 PSI). Simply fill the cup up with powder (works best at 1/2-3/4 full with aluminium oxide and 3/4 for dolomite). You may find that drying out your powders in the oven before using leads to better flow. Aluminium oxide runs best in this kit and is the powder we would recommend with the Paasche 99% of the time for ease of use, but we understand that some may wish to use dolomite from time to time as a more specialist powder. Dolomite often requires a bit more 'pumping' of the button to get it flowing, and may require drying out in the oven and the installation of more heavy duty air dryers (like a Dropout and Carbon Filter Kit). To learn more about the different powders in air abrasives, read this article. If you are looking at using dolomite full-time, you may wish to look at the Vaniman range. We can supply the kit with a Sparmax Silver Bullet Plus moisture trap that, when fitted, sits in the hand connected to the air eraser drying the air as it goes into the handpiece. You can adjust the airflow to the handpiece a little by using the bleed valve on the moisture trap. This is suitable if you are on a tight budget, but we would recommend a Dropout Filter which will not only dry the air exceptionally well, but also protect other air tools you are using on the same airline.If you are not already experienced in air abrasives, you will find that a lot of dust is generated. We recommend suitable dust extraction and working in a blast cabinet (this can be as makeshift as you like as long as it contains the mess!). This dust can be a health hazard and so please wear an FFP3 dust mask or a respirator as well as goggles whilst working.Air consumption 0.5 CFM - will run comfortably off most 24l compressors.Do not use with powders that exceed 70 microns in diameter.
The Paasche AEC Air Eraser is an entry-level air abrasive that is widely used in fossil preparation. The powder is held in the little cup on top and blasted through a tungsten carbide nozzle when you depress the button on top. This powder flow stops when the button is released. We have put together a kit so that it is ready to plug straight into your air compressor and get going! In this kit: Paasche Air Eraser Adaptors 2m Festo Air Hose Quick connector (PCL/Euro as per user requirements) FREE 100g sample of Aluminium Oxide powder FREE 100g sample of Dolomite powder Optional Sparmax Silver Bullet Plus with Bleed Valve Moisture Trap. For general work, use clean dry air at pressures of 2-3 Bars (30-45 PSI), going up to a maximum of 4.5 Bars (65 PSI). Simply fill the cup up with powder (works best at 1/2-3/4 full with aluminium oxide and 3/4 for dolomite). You may find that drying out your powders in the oven before using leads to better flow. Aluminium oxide runs best in this kit and is the powder we would recommend with the Paasche 99% of the time for ease of use, but we understand that some may wish to use dolomite from time to time as a more specialist powder. Dolomite often requires a bit more 'pumping' of the button to get it flowing, and may require drying out in the oven and the installation of more heavy duty air dryers (like a Dropout and Carbon Filter Kit). To learn more about the different powders in air abrasives, read this article. If you are looking at using dolomite full-time, you may wish to look at the Vaniman range. We can supply the kit with a Sparmax Silver Bullet Plus moisture trap that, when fitted, sits in the hand connected to the air eraser drying the air as it goes into the handpiece. You can adjust the airflow to the handpiece a little by using the bleed valve on the moisture trap. This is suitable if you are on a tight budget, but we would recommend a Dropout Filter which will not only dry the air exceptionally well, but also protect other air tools you are using on the same airline. If you are not already experienced in air abrasives, you will find that a lot of dust is generated. We recommend suitable dust extraction and working in a blast cabinet (this can be as makeshift as you like as long as it contains the mess!). This dust can be a health hazard and so please wear an FFP3 dust mask or a respirator as well as goggles whilst working. Air consumption 0.5 CFM - will run comfortably off most 24l compressors. Do not use with powders that exceed 70 microns in diameter.
The Paasche AEC Air Eraser is an entry-level air abrasive that is widely used in fossil preparation. The powder is held in the little cup on top and blasted through a tungsten carbide nozzle when you depress the button on top. This powder flow stops when the button is released.We have put together a kit so that it is ready to plug straight into your air compressor and get going!In this kit:Paasche Air EraserAdaptors2m Festo Air HoseQuick connector (PCL/Euro as per user requirements)FREE 100g sample of Aluminium Oxide powderFREE 100g sample of Dolomite powderOptional Sparmax Silver Bullet Plus with Bleed Valve Moisture Trap.For general work, use clean dry air at pressures of 2-3 Bars (30-45 PSI), going up to a maximum of 4.5 Bars (65 PSI). Simply fill the cup up with powder (works best at 1/2-3/4 full with aluminium oxide and 3/4 for dolomite). You may find that drying out your powders in the oven before using leads to better flow. Aluminium oxide runs best in this kit and is the powder we would recommend with the Paasche 99% of the time for ease of use, but we understand that some may wish to use dolomite from time to time as a more specialist powder. Dolomite often requires a bit more 'pumping' of the button to get it flowing, and may require drying out in the oven and the installation of more heavy duty air dryers (like a Dropout and Carbon Filter Kit). To learn more about the different powders in air abrasives, read this article. If you are looking at using dolomite full-time, you may wish to look at the Vaniman range. We can supply the kit with a Sparmax Silver Bullet Plus moisture trap that, when fitted, sits in the hand connected to the air eraser drying the air as it goes into the handpiece. You can adjust the airflow to the handpiece a little by using the bleed valve on the moisture trap. This is suitable if you are on a tight budget, but we would recommend a Dropout Filter which will not only dry the air exceptionally well, but also protect other air tools you are using on the same airline.If you are not already experienced in air abrasives, you will find that a lot of dust is generated. We recommend suitable dust extraction and working in a blast cabinet (this can be as makeshift as you like as long as it contains the mess!). This dust can be a health hazard and so please wear an FFP3 dust mask or a respirator as well as goggles whilst working.Air consumption 0.5 CFM - will run comfortably off most 24l compressors.Do not use with powders that exceed 70 microns in diameter.
The Paasche AEC Air Eraser is an entry-level air abrasive that is widely used in fossil preparation. The powder is held in the little cup on top and blasted through a tungsten carbide nozzle when you depress the button on top. This powder flow stops when the button is released. We have put together a kit so that it is ready to plug straight into your air compressor and get going! In this kit: Paasche Air Eraser Adaptors 2m Festo Air Hose Quick connector (PCL/Euro as per user requirements) FREE 100g sample of Aluminium Oxide powder FREE 100g sample of Dolomite powder Optional Sparmax Silver Bullet Plus with Bleed Valve Moisture Trap. For general work, use clean dry air at pressures of 2-3 Bars (30-45 PSI), going up to a maximum of 4.5 Bars (65 PSI). Simply fill the cup up with powder (works best at 1/2-3/4 full with aluminium oxide and 3/4 for dolomite). You may find that drying out your powders in the oven before using leads to better flow. Aluminium oxide runs best in this kit and is the powder we would recommend with the Paasche 99% of the time for ease of use, but we understand that some may wish to use dolomite from time to time as a more specialist powder. Dolomite often requires a bit more 'pumping' of the button to get it flowing, and may require drying out in the oven and the installation of more heavy duty air dryers (like a Dropout and Carbon Filter Kit). To learn more about the different powders in air abrasives, read this article. If you are looking at using dolomite full-time, you may wish to look at the Vaniman range. We can supply the kit with a Sparmax Silver Bullet Plus moisture trap that, when fitted, sits in the hand connected to the air eraser drying the air as it goes into the handpiece. You can adjust the airflow to the handpiece a little by using the bleed valve on the moisture trap. This is suitable if you are on a tight budget, but we would recommend a Dropout Filter which will not only dry the air exceptionally well, but also protect other air tools you are using on the same airline. If you are not already experienced in air abrasives, you will find that a lot of dust is generated. We recommend suitable dust extraction and working in a blast cabinet (this can be as makeshift as you like as long as it contains the mess!). This dust can be a health hazard and so please wear an FFP3 dust mask or a respirator as well as goggles whilst working. Air consumption 0.5 CFM - will run comfortably off most 24l compressors. Do not use with powders that exceed 70 microns in diameter.
Airbrush Kit - Save on this Airbrush and Compressor Kit
sale Airbrush Paasche Talon TG 0.25 - 0.38 - 0.66 mm
Update - Paasche Aecr Remote Air Eraser Etching Tool : -) - Fossil
ZOIC PALAEOTECH Deals Discounted
Iwata Professional Mobile Make-Up Kit with Ninja Jet Compressor
Paasche Air Eraser Kit
Paasche Air Eraser Kit (ready to plug into air compressor
Silentaire - Super Silent 30-TC
Air Erasers, Sandblasters & Compounds
Paasche Air Eraser Kit (ready to plug into air compressor)
TG-300R Making Quality Spray Paint Equipment in the US Since 1904
This kit comes complete with dust mask, 6' braided hose and 6 ounces for fast cutting compound. The air eraser can be used anywhere an abrasive is required to delicately erase; such as decorative etching on glass. Can also be used by the professional technician, manufacturer, hobbyist or for dental lab work, erasing color, and removing rust. Requires a compressor 1/3 HP or larger that can deliver up to 70 PSI.
Paasche AEC-K Air Eraser Kit
DC850R Making Quality Spray Paint Equipment in the US Since 1904
Recommended for you
-
Paasche HS Single Airbrush Set - HS-3AS18 Jun 2024
-
Paasche Airbrush VLSTPRO#3L Professional Airbrush No accessories PAASC18 Jun 2024
-
Paasche Airbrush TG-3AS Gravity Feed Airbrush-PBTG-3AS18 Jun 2024
-
Paasche Airbrush VLS-3-191 Airbrush Sets — CHIMIYA18 Jun 2024
-
Chroma Craft, LLC. - Paasche® VL™ Model Airbrush Set18 Jun 2024
-
Paasche H Airbrush Set - Paxton/Patterson18 Jun 2024
-
Paasche VL-3W Wood Box Set with All Three Heads for VL Airbrush, 1 - Fry's Food Stores18 Jun 2024
-
Paasche EZ-STARTER Single Action Beginners Airbrush Set on sale18 Jun 2024
-
Paasche Airbrush 2000H Airbrush Sets, None18 Jun 2024
-
Paasche TG-100D Gravity Feed Airbrush & Compressor Package18 Jun 2024
You may also like
-
How to Plant, Grow, and Harvest Calendula Herb - Harvest to Table18 Jun 2024
-
This Is Car Interior Leather Repair Agent Car Leather Crack Repair18 Jun 2024
-
Milwaukee M18 FUEL Sectional Machine with 5/8inch Cable 2818B-21 - Acme Tools18 Jun 2024
-
Taylor Jewelry Box, Swiftie Necklace Gold, Swift Merch, Albums & Eras Tour Inspired Small Travel Jewelry Case for TS Fans, Music Lover Gifts Travel Jewelry Box …18 Jun 2024
-
White Faux Fur Trim18 Jun 2024
-
DIY Digital Oil Painting By Number Kit Linen Canvas Paint Home Decor18 Jun 2024
-
Best gold table decorations for Christmas - Christmas decorations18 Jun 2024
-
Rhetoric of a Fangirl18 Jun 2024
-
Buy Touch Markers Colour Set Twin Tip Graphic Art Set Sketch 36 4818 Jun 2024
-
Buy Wholesale China Hot Sales Colored Glass Candle Holders Candle Jar With Gift Box Jar Candles For Wedding Decoration & Candle Jars Candle Glass Jar at USD 0.4918 Jun 2024